FPV Drone Budget Build Full Tutorial – Part 1 – Assembly

FPV Drone Budget Build Full Tutorial – Part 1 – Assembly



Uncertain about what to purchase? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate-fpv-shopping-list

SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia

THIS IS MY FULL TIME JOB. Here are different methods which you could assist me: https://www.fpvknowitall.com/support-me/

It’s time to replace my FPV Drone Budget Build. This is not the most cost effective FPV quadcopter you may construct. But I imagine it is the most effective worth for cash. And I’ve partnered with GetFPV to assist just remember to can purchase all of the components you want in a single straightforward package.

— VIDEO REFERENCE LINKS —

Beginner solder tutorial – https://www.youtube.com/watch?v=Qps9woUGkvI

More in-depth tutorial in basic 60’s model (however nonetheless 100% related) – https://www.youtube.com/watch?v=vIT4ra6Mo0s

Watch the remainder of this playlist at:
https://www.youtube.com/playlist?list=PLwoDb7WF6c8mwruPq4rxwAKhUFS08pxi9

— PRODUCT LINKS —

I obtain a fee (at no additional price to you) for those who make a purchase order after clicking one of many affiliate hyperlinks under.

Purchase this drone construct package at GetFPV:
* DJI Version – http://bit.ly/3rvflJX
* Analog Version – https://bit.ly/2ZG6skz

Tools used on this construct embody:

https://bit.ly/2Z5HCLX – Ethix Tool Case contains hex drivers, wire cutter & stripper, prop wrench, and different necessities.

https://bit.ly/3f0b9MB – Sequre transportable soldering iron punches method above its weight at round $35

http://amzn.to/2CEK2nG – Aouye bench-top soldering iron. Better ergonomics than Sequre and plugs straight into the wall, however not transportable.

https://bit.ly/3e1MQfT – Kester rosin-core leaded solder

https://bit.ly/3gBAvk7 – Kester flux pen

https://bit.ly/2ZMkaCJ – Smoke Stopper

http://amzn.to/2o8LdTO – Innova 3320 multimeter

http://amzn.to/2tIeE1X – Hakko CHP-170 flush-cutter

http://amzn.to/2gM7kAV – Blue-tack mounting putty

http://amzn.to/2uJ91Vw – Briggs Precision Kelley forceps

http://amzn.to/2eWxhxM – Cross-lock tweezers

http://amzn.to/2eNJnFv – 3M Super 35 electrical tape

http://amzn.to/2jegIi5 – 3M 4011 excessive mounting tape

https://amzn.to/2sPBJCa – Kapton tape

http://amzn.to/2eQ5uLu – Heat shrink assortment

http://amzn.to/2gRJv8E – Blue thread locker

MANDATORY DISCLAIMER: I’m a participant within the Amazon Services LLC Associates Program, an affiliate promoting program designed to offer a way for me to earn charges by linking to Amazon.com and affiliated websites.

Most or all hyperlinks above are affiliate hyperlinks, and I’ll obtain compensation for those who use them.

— TABLE OF CONTENTS —

0:00 – Introduction
2:46 – Assemble the body base plate
7:18 – Install motors
10:26 – Solder fundamental battery wires to ESC
17:54 – Solder capacitor to battery pads
21:51 – Solder motor wires to ESC
28:29 – Solder XT60 connector to fundamental battery wires
32:37 – Plug in FC to ESC and mount
35:34 – Mount vTX
37:27 – Wire up digicam
41:33 – Wire up vTX
45:17 – Wire up receiver
50:25 – Smoke verify

source